TOP page

Wireless LAN setup with a setup window (Usual settings)

Set up wireless LAN manually with setup window of this product.
This product can register up to 4 SSIDs (wireless LAN group). It can be used as if there are multiple wireless LAN access points with one product.

*Please refer to here If you want to check the initial setup for the wireless LAN access point.

WEP settings

WPA/WPA2 settings


  
WEP settings

Please set the "Channel BandWidth"
to "20/40" when using the 150Mbps highspeed wireless LAN transmission on 802.11n.

Connect this product to the PC with LAN cable.


Connect a LAN cable in the case of setup.

 


Turn on the power and start the web browser.

 

Enter the IP address "192.168.1.1" into the address column, and press <Enter> key.


(1)Enter "admin" in "User name" with half-width characters.
(2)Enter "password" into "Password" with half-width characters.
(3)Click [OK].

 

Click "Wireless" - "Basic".


These steps tell you how to set the network name in the "Multiple SSID1".

(1)Enter arbitrarily network name* with half-width characters.
*Default setting is"planexuser".
(2)Click [Apply]



This product will restart.  It will take around 2 mins to start up this product again.

You can enter up to 32 half-width characters.
    SSID is needed when setting it up on the PC which carries out wireless LAN communication, So we recommend you write down the SSID.



Click "Wireless" - "Security".


Set up the Encryption (security).



(1)Select "SSID".
*"planexuser" is selected on this procedure.

(2)Select "Open System" or "Shared key" or "AUTO(Open/Shared)".
"Open System": It authenticates and communicates irrespective of the existence of the WEP key.
"Shared key": It authenticates by using the WEP key, and communication is possible only when it has the same WEP key.
*Usually "AUTO(Open/Shared)"is selected.

(3)Select from "Key 1" to "Key 4".
*"Key 1" is usually selected.

(4)Enter the WEP key arbitrarily with one-byte characters.
The number of characters to be set will be different. Please refer to the followings
*64bit or 128bit is automatically recognized.

 
When entering ASCII.
When entering a hexadecimal number
When setting up WEP(64bit)
5 half-width characters
10 digit hexadecimal numbers
When setting up WEP(128bit)
13 half-width characters
26 digit hexadecimal numbers

*The text to be entered with hexadecimal numbers is for Numeral "0-9" and for alphabetic character "A-F, a-f".
*Please be careful not to mix up "8" and "B",
*Please be careful not to mix up "0" and "O",

(5)Select "Hex" or "ASCII".
*Wnen you enter WEP key with the " 5 English one byte characters" or "13 English one byte characters", select "ASCII".
*When setting WEP key with "10-digit hexadecimal numbers" or "26-digit hexadecimal numbers", select "Hex".

(6) Click [Apply].

Please set up the following articles, If it's necessary.
Policy Controlling the wireless LAN client to connect to.
"Allow": It approves the internet connection only for the registered MAC address.
"Reject": It rejects the internet connection only for the registered MAC address.
"Disable" : The restriction is disable.
*A maximum of 8 pieces can be registered.
You can not register "Allow" and "Reject" together.
Default Setting : Disable
Add a station Mac Enter the MAC address to be controlled. (Example:XX:XX:XX:XX:XX:XX)

Close the window.

Setup is completed.



Please set the same wireless settings here to a wireless client. Wireless communications can be performed by making the same setup to this product and a wireless client


  
WPA/WPA2 settings

Please set the "Channel BandWidth" to "20/40"at the following when using the 150Mbps
highspeed wireless LAN transmission.

Connect this product to the PC with the LAN cable.


Connect a LAN cable in the case of setup.

 


Turn on the power and start the web browser.

 

Enter the IP address "192.168.1.1" into the address column, and press <Enter> key.


(1)Enter "admin" in "User name" with half-width characters.
(2)Enter "password" into "Password" with half-width characters.
(3)Click [OK].

 

Click "Wireless" - "Basic".


These steps tell you how to set the network name in the "Multiple SSID1".

(1)Enter arbitrarily network name* with half-width characters.
*Default Setting is"planexuser"
(2) Click [Apply]



This product will restart.  It will take around 2 mins to start up this product again.

*You can enter up to 32 English half-width characters.
    SSID is needed when setting it up on the PC which carries out wireless LAN communication, So we recommend you write down the SSID.



Click "Wireless" - "Security".


Set up the Encryption (security).


About WPA/WPA2
WPA/WPA2 is a security standard of the wireless LAN which strength WEP. In WPA-PSK/WPA2-PSK, an encrypting key is used to be called a pre-shared key and set the common encrypting key to an access point and a client same as WEP.
In WPA2, "AES" is standardized and its security is more robust than WPA.

*This product supports the IEEE802.1X certification, but it is out of support.

The setting value set up here is needed when setting it to PC which conducts wireless communications. We recommend you write down the value set.

(1)Select "SSID".
*"planexuser" is selected on this procedure.

(2) Select from"WPA" "WPA-PSK" "WPA2" "WPA2-PSK" "WPA-PSK/WPA2-PSK" "WPA/WPA2".
* "WPA2-PSK" is usually selected.

(3)Select from "TKIP", "AES", "TKIP/AES".
* "AES" is usually selected.
*The intensity security for "AES" is more higher than "TKIP".
*If TKIP/AES is selected, they can communicate mutually in the network where "TKIP" and "AES" were intermingled.
*When it is "WPA" "WPA-PSK", it does not support "TKIP/AES".

(4)Enter the pass phrase.

 
When entering ASCII
When entering it by hexadecimal number
Pass phrase
8∼63 English one byte characters
64 digit hexadecimal numbers

*The text to be entered with hexadecimal numbers is for Numeral "0-9" and for alphabetic character "A-F, a-f".

*Please be careful not to mix up "8" and "B",
*Please be careful not to mix up "0" and "O",

(5) Click [Apply].

Please set up the following articles, If it's necessary.
Policy Controlling the wireless LAN client to connect to.
"Allow": It approves the internet connection only for the registered MAC address.
"Reject": It rejects the internet connection only for the registered MAC address.
"Disable": The restriction is disable.
*A maximum of 8 pieces can be registered.
*You can not register "Allow" and "Reject" together.
Default Setting : Disable
Add a station Mac Enter the MAC address to be controlled (Example: XX:XX:XX:XX:XX:XX)


Close the window.

Setup is completed.



Please conduct the same wireless setup set to this product here to a wireless LAN client(Adapter). Wireless communications can be performed by making the same setup for this product and a wireless client.

  Back to the Menu  
 
(C)Copyright 2006 PLANEX COMMUNICATIONS Inc. All rights reserved